BILGE PUMPS

Products within this category:

BILGE PUMP SWITCH PANEL

BILGE PUMP SWITCH PANEL

The Osculati bilge pump control panel allows 3 settings for control of any bilge pump with an automatic float switch. The switch panel has control LED lights, a rocker switch with 3 positions (automatic, off or manual). The panel features a loud and bright alarm system to indicate the water level of the bilge. The bilge pump switch panel is made from black plastic and is fused.

£22.00

More Details >

FLOAT SWITCH WHALE

FLOAT SWITCH WHALE

Whale BE9002 float switch designed for use with the range of Orca and standard Supersub bilge pumps. This compact float switch is suitable for bulkhead or hull mounting in the bilge to operate electric bilge pumps. When installed vertically, this float switch can also be used as a high bilge water alarm.


The bilge pump switch is environmentally friendly as it doesn't contain mercury like some other switches.

£22.00

More Details >

JABSCO BILGE PUMP SWITCH

JABSCO BILGE PUMP SWITCH

The Rule model 43 allows 3 settings for control of any bilge pump with an automatic float switch. The switch panel has a built-in fuse holder (fuse not supplied) and an internally lit rocker switch with 3 positions (automatic, off or manual). The panel has a "fail-safe" spring to return to the "off" position from the "manual" position. The bilge pump switch panel is made from black plastic.

£29.00

More Details >

RULE 20SA 800 AUTO

RULE 20SA 800 AUTO

The Jabsco Rule 20SA 800 series automatic submersible bilge pump with 750mm cable eliminates the need for a separate float switch to activate the pump. Once power is supplied to the bilge pump, starting and stopping is completely automatic.


The Rule automatic bilge pump turns on and checks for water every 2 1/2 minutes, during this check the pump runs for approximately 1/2 a second and checks for resistance or drag against the impeller. If resistance is encountered, it will run until water is no longer present. Thereafter the automatic bilge pump resumes the 2 1/2 minute check cycle. The automatic bilge pump can be started at any time by turning the power off; waiting 5 seconds and then turning the power back on. The pump will start immediately and pump until the water is removed.


The Rule automatic submersible bilge pump is a light weight, compact pump with a tough plastic body and integral strainer. The automatic bilge pump features two leads, an automatic (brown) and a manual override (brown with a white stripe). The quick release strainer allows for rapid cleaning of the submersible bilge pump internal components.


The Rule 800 series of small submersible bilge pumps are recommended for discharge heads up to a maximum of 2 metres. The submersible bilge pump meets ISO8846 marine (ignition) and ISO8849 marine (bilge pump) standards.


The power use during the checking mode is minimal, the bilge pump will consume 0.20 amp hours per day in the checking mode.


Please note - Output is based on 10 hour break-in period and at 13.6V, a minimum voltage of 10.5V is required.

£71.00

More Details >

RULE 25DA 500

RULE 25DA 500

Rule 25DA 500 Series submersible bilge pump with a flow rate of up to 31 litres per minute (8 gallons).


The Rule submersible bilge pump is a light weight, compact pump with a tough plastic body and integral strainer. The quick release strainer allows for rapid cleaning of the submersible bilge pump internal components.


The Rule 500 range of small submersible bilge pumps are recommended for discharge heads up to a maximum of 2 metres. The submersible bilge pump meets ISO8846 marine (ignition) and ISO8849 marine (bilge pump) standards.

£25.00

More Details >

RULE 25SA 500 AUTO

RULE 25SA 500 AUTO

The Jabsco Rule 25SA 500 series automatic submersible bilge pump with 750mm cable eliminates the need for a separate float switch to activate the pump. Once power is supplied to the bilge pump, starting and stopping is completely automatic.


The Rule automatic bilge pump turns on and checks for water every 2 1/2 minutes, during this check the pump runs for approximately 1/2 a second and checks for resistance or drag against the impeller. If resistance is encountered, it will run until water is no longer present. Thereafter the automatic bilge pump resumes the 2 1/2 minute check cycle. The automatic bilge pump can be started at any time by turning the power off; waiting 5 seconds and then turning the power back on. The pump will start immediately and pump until the water is removed.


The Rule automatic submersible bilge pump is a light weight, compact pump with a tough plastic body and integral strainer. The automatic bilge pump features two leads, an automatic (brown) and a manual override (brown with a white stripe). The quick release strainer allows for rapid cleaning of the submersible bilge pump internal components.


The Rule 500 series of small submersible bilge pumps are recommended for discharge heads up to a maximum of 2 metres. The submersible bilge pump meets ISO8846 marine (ignition) and ISO8849 marine (bilge pump) standards.


The power use during the checking mode is minimal, the bilge pump will consume 0.20 amp hours per day in the checking mode.


Please note - Output is based on 10 hour break-in period and at 13.6V, a minimum voltage of 10.5V is required.

£57.00

More Details >

RULE 27DA 1100

RULE 27DA 1100

Rule 27DA 1100 Series submersible bilge pump with a flow rate of up to 69 litres per minute (18 gallons).


The Rule submersible bilge pump is a light weight, compact pump with a tough plastic body and integral strainer. The quick release strainer allows for rapid cleaning of the submersible bilge pump internal components.


The Rule 1100 range of small submersible bilge pumps are recommended for discharge heads up to a maximum of 2 metres. The submersible bilge pump meets ISO8846 marine (ignition) and ISO8849 marine (bilge pump) standards.

£35.00

More Details >